How To Repair A Broken Sprinkler Pipe

Download Article

Download Article

If there are areas of your lawn that look more similar to a marsh than a backyard, y'all may take broken sprinkler pipes. Fortunately, fixing the problem isn't also hard if you don't mind getting dirty.

Steps

1. 1

   Ensure you have all the required supplies. Zero is worse than having to run to the hardware shop in the middle of a projection. Encounter the list of things you need below.

2. 2

   Observe the rupture. Commonly a soggy area of grass, just sometimes it is a geyser.

   Advertisement

3. iii

   Plough off the sprinklers, if y'all don't this could be a very hard job.

4. 4

   Dig upwards the pipe. Not the whole pipe, only the section that is broken. Advisedly remove the section of grass higher up the piping, trying to go along it intact. Practise this by cut a circular department with the end of your shovel above where you are to dig and so carefully lifting it off. Dig up the clay in a higher place the bad pipe with a shovel (you will probably too need a manus trowel to dig up the dirt under the pipe). You lot will desire to accept at least 6 inches (15.2 cm) on each side of the break articulate and enough room for you fist underneath the pipe. If the hole fills with water, you will either have to wait for it to dry or bail it out (the latter is recommended).

5. 5

   Cutting the pipe. Get a hacksaw, PVC or metallic pipe cutters (depending on what type of pipe you take, older sprinkler systems are normally metallic, while newer ones tend to be PVC). Cut the broken section out and then that you take clean, undamaged pipage on both sides.

6. half-dozen

   Measure a new length of pipe that is just a fleck shorter than the gap left by erstwhile pipe that you cut abroad. It should probably be i/2 " to 1" shorter to allow room for the connectors. Or you tin can buy a PVC plumbing fixtures from near domicile improvement stores that has one pipe sliding inside an outer barrel with an O-ring inside. It will extend most iii" in length. You may see in stores i/2" to 2 1/ii" in diameter sizes. I end is a female person slip and the other is a male that needs a coupling, elbow, or tee to connect to complete the repair.

7. seven

   Clean the piping. Some water will come pouring out at outset, you could endeavour to take hold of it, but information technology is easier to bail it out. Once the water stops coming out, clean both ends with a rag.

8. viii

   Fit the new section. If y'all are lucky enough to have PVC then you just put the PVC primer and glue on the outside of the pipage and inside of the straight connectors and slip them together. Work quickly because the mucilage sets fast. Then put the section you lot just glued in the gap yous merely created, repeating the gluing process. If y'all have metal pipes you will take to thread the outside of the pipage to fit the connectors rather than gluing them.

9. ix

   Test the pipage. Turn the sprinklers back on and brand certain information technology is sealed properly.

10. 10

    If everything is fixed, encompass upwards the pigsty and supersede the grass you so advisedly removed before.

    Advertizement

Ask a Question

200 characters left

Include your email address to go a bulletin when this question is answered.

Submit

Advertisement

Thanks for submitting a tip for review!

• Be careful when digging, you never know what y'all might hit with your shovel.

Advert

Things You'll Need

• Shovel & trowel
• Piping
• 2 straight connectors
• hacksaw or piping cutter
• for PVC, glue and primer
• for metal, a threader
• Rags
• 2 Hours

About This Commodity

Thanks to all authors for creating a folio that has been read 51,916 times.

Did this article help you?

How To Repair A Broken Sprinkler Pipe,

Source: https://www.wikihow.com/Fix-a-Broken-Sprinkler-Pipe

Posted by: carnesadving.blogspot.com

Share this post